Fume Hood
A fume hood (sometimes called a fume cupboard or fume closet) is a type of local ventilation device that is designed to limit exposure to hazardous or toxic fumes, vapors or dusts.
Features
- Durable and chemical resistant
- We provide benchtop, Distillation & Floor Mounted Fume hoods
- Opt for MOC in either SS, MS or Wood
- Designed as per ASHRAE 110
Lab Furniture
SLI Adaptable systems are designed to meet the needs of
the modern laboratory, where flexibility and adjustability are
essential
Features
- Based upon available footprints, the furniture can be customized at the concept stage itself.
- Based upon available footprints, the furniture can be customized at the concept stage itself.
- Based upon available footprints, the furniture can be customized at the concept stage itself.
Solvent Cabinet
A solvent cabinet must incorporate a number of safety features. It should be
adequately ventilated, preventing the release of excessive fumes (being either
sealed or vented). It should be equipped to contain fires and isolate the
contents from sources of ignition, be grounded (to prevent sparks and static
discharge).
Features
- Opt for MOC in either MS or PP
- Adjustable trays to meet your solvent container size
- Easy to access and proper ventilation
Gas Purification & Control System
The Gas Purification and Controller system is designed to remove oxygen, moisture,
hydrocarbons, oil and other foreign materials from gas streams. The system eliminates noise
and unaccepted signals of gases in order to obtain peak resolution and peak tailing in the
analysis.
Features
- Improves reproducibility of analysis
- Reduce baseline noise, drift problems, etc
- Increase column life preferably for polar & capillary columns
- Deliver better than UHP grade gases
- Increase detector life & reduces flame problem
- Save costly gases through toggle valves & gas distribution panel
Gas Distribution Panel & Selector Box
Gas distribution panel is used when there is more than one Gas
Chromatograph. It helps to control the flow & pressure of different
gases for different GC’s.
Features
- Capable of handling fouling liquids.
- Steam economy is improved by using Multiple effect arrangement thus saving the product cost
- Trace quantities of suspended particles in feed are tolerated.
Gas Manifold System
High pressure Mechanical- Automatic Gas Manifold is used for a two cylinder system where
automatically switching over is required from one cylinder to other, when the pressure in the
one cylinder is below the set pressure. It can be used for multiple cylinders banks
Features
- Adjustable single stage line regulator 0 - 125 and 0 – 200 psig.
- Flexible stainless braided pigtails (except Oxygen service – rigid copper pigtails provided per NFPA 99)
- CGA gas specific pigtail connections.
- Complete system cleaned for use with Oxygen..
Rotameter
A rotameter is a device that measures the volumetric flow rate of fluid in a closed tube. It
belongs to a class of meters called variable-area flowmeters, which measure flow rate by
allowing the cross-sectional area the fluid travels through to vary, causing a measurable effect.
Features
- Rangeability is better.
- It is easily equipped with alarms and switches or any transmitting devices.
- It also measures the flow rate of corrosive fluids.
- There is an availability of viscosity-immune floats.
Inline Micron Filter
Inline Micron Filters are used to remove dust particles from respective gases. Micron filter (SS
body) consists of SS disc (Mesh) of 5μ – 10μ. Gas purification panel removes impurities which
are in vapours (gases) form.
Features
- Available in material SS316.
- Material Traceable to certified material test report
- Remove system particulate contaminants.
- Inline Filters are for use where space is limited.
- Inline Filters are for use where space is limited.
- Variety of end configuration includes.
- SEALEXCEL Well-Lok Tube Fittings, Male / Female NPT, BSPT, BSPP pipe connections
Gas Sampling Bomb/Bottle
Gas Sampling Bomb that are specially designed to collect and store high pressure gas samples
from the field & transport the same to laboratories.
Features
- Used to store oil/gas samples
- Ensure maximum integrity
- Effective corrosion resistance
- Athena Gas/Oil Sampling Bottles are manufactured in S.S. 316/304 construction.
- Each bottle is tested to hydraulic test pressure of 250 bar.
- Suitable for working pressure of 150 bar.
Air Header
Air Headers is a substitute for multiple valve assemblies, which normally operates from one
originating point. The Air Manifolds are configured for accommodating various outlet valves.
The inlet-connection can have a variety of end connections.
Features
- Lockable handles as standard prevent accidental manual actuation of outlet valves.
- Durable & Reliable
- Reduction in assembly time
- Lightweight ball valve design
- Robust.
Automatic Mechanical Gas Change Over
High pressure Mechanical- Automatic Gas Manifold is
used for a two cylinder system where automatically
switching over is required from one cylinder to other,
when the pressure in the one cylinder is below the set
pressure. Setting of pressure of two cylinder can be set
as per user requirement
Features
- Inlet Pressure Gauge : 2 nos.0-210kg/cm2Gauge
- Outlet Pressure Gauge : 1 no.0-14kg/cm2Gauge/as per Requirement.
- Flow : 300 LPH (MAX).
- Gas services : Air, N2, H2, He, Ace, Arg, N2, P10 and other gas & also for flammable / nonflammable & corrosive gases.
- Outlet Connection : ¼” OD ferrule fitting with ball valve
- Inlet Connection :¼” BSP male to suit pigtail coming from cylinder
Tubing/ Casing Capping
Tubing are available in different sizes like 1/2″, 1/4″, 1/8″,
1/16″. Tubing available in different MOC like copper, S.S.,
teflon, nylon. Casing capping is used to cover the above tubing
& to maintain the esthetic look. Three types of casing capping
available, M.S. powder coated, aluminium powder coated & PVC casing capping.
Features
- Steady Performance
- High Crack Resistant
- Long Life
- Easy to Use
Cylinder Trolley
Features
- Cylinder trolley in MS powder coated 4 wheels for smooth safe operation
- Cylinder trolley available for single two cylinders
- Cylinder mounting brackets are used to mount the cylinder on a wall to avoid down fall of a cylinder.
Gas Cylinder Regulator
There are two basic types of gas pressure regulators: single-stage and two-stage. Single-stage
pressure regulators reduce the cylinder pressure to the delivery or outlet pressure in one step.
Two-stage pressure regulators reduce the cylinder pressure to a working level in two steps.
Features
- Two types of Cylinder Regulators are available: Brass chrome plated body with SS Diaphragm and SS body with SS Diaphragm.
- Regulator Consist of inlet & outlet pressure gauges. Inlet pressure gauge shows the total pressure of cylinder and outlet pressure gauge shows regulated pressure and Pre- Heater.
- It is used for special gases Nitrous Oxide & CO2.
- Inlet pressure range : 0-240 Kg / cm2
- Outlet pressure range : 0-14 kg /cm2 in diaphragm type.
Gas Detection System
Features
- Dual display of gas concentration & set point/ unit of the gas
- Plug in smart field proven sensor
- Programmable linear 4-20mA/ 20-4mA O/P with respect to gas concentration
- Easy one man calibration at site
- Optional RS-485 with modbus RTU protocol
- Suitable in hazardous areas ATEX, CCOE, CMRI & IP-65 approved.
HCL Gas Regulator
Features
- Single-stage pressure reducer
- Maternal and diaphragm use hard seal form
- Body NPT inlet and outlet interface 1/4''NPT(F)
- The internal structure easy to purge
- Can set filters
- Can use a panelInstallation
- Inlet form Needle valve, membrane valve
Cylinder Trolley
Features
- Cylinder trolley in MS powder coated 4 wheels for smooth safe operation
- Cylinder trolley available for single two cylinders
- Cylinder mounting brackets are used to mount the cylinder on a wall to avoid down fall of a cylinder.
Laser Cutting Gas Regulator
The regulator is specifically designed to meet the high flow, high pressure assist gas
requirements of the laser cutter. It has fast on-off-on response, high flow capacity, and delivers
the pressures required for the job. Whether your source gas is cryogenic or high pressure, this
regulator can handle the job. The regulator is actually two regulators in one body – a
dome-loaded piston regulator with a sensitive diaphragm actuated dome loader built in.
Features
- Rapid on-off-on response even at high flow rates.
- 1/2” NPT female inlet and outlet connections.
- High flow capacity Cv = 0.55.
- Minimal delivery pressure decay (0.3 psi/100 psi)
- Built-in dome loader regulator
- Bonnet threaded to accept panel nut.
- Encapsulated seats with 10 micron filter.
Toggle Valve
Toggle valves are pieces of equipment that allow the user to control the flow of fluid via a
directional toggle switch. They are typically used in conditions with moderate temperatures and
pressure applications. When you have three or four-way toggle valves give you multiple options
for flow rates. These pieces tend to come with a wide range of materials, sizes and connection
types.
Features
- Quick opening and closing
- Straight and angle patterns available
- Stainless steel or brass construction
- Standard Black Bylon handle or optional stainless steel handle
- Tube Fitting, female NPT, and Male NPT end connection
- Orifice Range – from 0.080 to 0.250 in (2.0 to 6.4mm)
High Pressure Hose Pipe
In chemistry and medicine, hoses (usually called tubes) are used to move
liquid chemicals or gases around. A fuel hose carries fuel. In the oil industry
high pressure hoses are used to move liquids under high pressures. Typical
uses are for kill and choke lines, cement lines and Kelly hose.
SS Braided High Pressure Pigtail
A hose is a flexible hollow tube designed to carry fluids from one
location to another. Hoses are Common factors are size, pressure
rating, weight, length, straight hose or coilhose, and chemical
compatibility. Applications mostly use nylon, Other hose materials
include PTFE (Teflon), stainless steel, and other metals.
Non Return Valve
A non-return valve allows a medium to flow in only one direction and is fitted to ensure that the
medium flows through a pipe in the right direction, where pressure conditions may otherwise cause
reversed flow
Features
- Low maintenance
- Accurate dimension
- Durable
Back Pressure Regulator
A Back Pressure Regulator (BPR) is a device that maintains a defined
pressure upstream of itself, at its own inlet. When fluid pressure at the
inlet exceeds the setpoint, the valve opens to relieve the excess
pressure.The lower pressure at the outlet attempts to hold the
diaphragm in a leak-tight seal with the orifice.
A back pressure regulator can be used to control pressure of any fluid
– gas, liquid or a mixture in a system. Most pumping applications
require back pressure to be maintained on the outlet of a pump.
Water /Oil Bath
A water bath is laboratory equipment made from a container filled
with heated water. For all water baths, it can be used up to 99.9
°C. When temperature is above 100 °C, alternative methods such
as oil bath, silicone bath or sand bath may be used.
Digital Temperature Indicator
With the help of well-trained professionals, we are engaged in offering
Digital Temperature Indicator to our clients. The offered indicators are
made available in various sizes to cater to the varied customer needs.
Extensively used in interfacing with specified RTD sensor and T/C, these
indicators are highly admired in the market. Customers can avail these
indicators at market leading prices.
Cylinder Holding Bracket
Riding on unfathomable volumes of industrial expertise, we are
offering a commendable assortment of Single Cylinder Holding
Bracket & Chain. The offered cylinders are provided in several
specifications as per the needs of customers. These cylinders
are manufactured by our team of professionals utilizing high
grade materials and leading technology. Provided in various
stipulations, we offer these cylinders are availed in market
leading rates.
Laboratory GlassWare
We also deal in glasses and provide all the accessories associated
with it. All the Industrial glass wares are available with us. We can
also customize the unit based upon customer requirement. We can
also offer rotavapor flasks of variable volumes and skid mounted
50,100 & 200 Liter Distillation Units.
Trolley
Lab Jack
Accessories
- 3 Finger Clamp
- Stand Base : Normal Duty : Medium Duty : Heavy Duty